-
1 mean value of modulus
Автоматика: среднее значение модуля -
2 mean value of modulus
English-Russian dictionary of mechanical engineering and automation > mean value of modulus
-
3 final mean value of modulus of elasticity
окончательное среднее значение модуля упругости
Emean,fin
—
[Англо-русский словарь по проектированию строительных конструкций. МНТКС, Москва, 2011]Тематики
Синонимы
- Emean,fin
EN
Англо-русский словарь нормативно-технической терминологии > final mean value of modulus of elasticity
-
4 value
1) значение; величина; параметр2) стоимость; цена3) оценка || оценивать•- acceptable value
- accumulative value
- active value
- actual value
- agreed value
- allowable value
- average value of size
- average value
- best value
- braking value
- certainty value
- characteristic value
- CLA value
- closeness value
- component value
- computed value
- conjugate value
- constant value
- continuous value
- controlled value
- conventional true value
- corrected parameter value
- corrected value
- correction value
- cutoff value
- cutting value
- default value
- depth-of-cut value
- design value
- desired value
- dimension value
- dimensional value
- disengaging value
- division value
- effective value
- equilibrium value
- final value
- fundamental value
- gray level values
- gray value
- hold value of contact
- ideal final value
- ideal value
- index value
- information value
- instantaneous value
- instruction value
- jog increment value
- just value
- landmark value
- level change value
- limit value
- limiting continuous value
- limiting dynamic value
- limiting thermal withstand value
- limiting value
- lubrication value
- master OOR value
- master value
- mean value of modulus
- mean value
- measured value
- minimum grade value
- model estimated value
- must value
- must-not-operate value
- NC value
- nominal value
- nonoperate value
- nonrelease value
- nonrevert value
- numerical value
- observation value
- offset value
- operate value
- operating value of quantity of electrical relay
- output value per employee
- output value
- part-program value
- peak value
- peak-to-peak value
- performance value
- pick feed value
- pickup value
- positional values
- preselected value
- preset value
- prestored value
- qualitative values
- quantity value
- rated value
- reference value
- release value
- resetting value
- reversal value
- RMS value
- root-mean-square value
- sampled values
- saturation value of the contact
- set point value
- set value
- setting value of a specified time
- setting value
- short-duration value
- short-time value
- stable value
- starting value
- steady-state value
- switching value
- target value
- test value
- thermal value
- thermal withstand value
- threshold value
- tool offset value
- true value
- value of a quantity
- value of reading
- value of the graduation
- value of the smallest graduation
- value of train
- variation value
- VB value
- weight removal value
- weighted value
- yield valueEnglish-Russian dictionary of mechanical engineering and automation > value
-
5 theorem
- analytical hierarchy theorem - arithmetical hierarchy theorem - closed range theorem - formally provable theorem - implicit function theorem - initial value theorem - integral representation theorem - local limit theorem - maximal ergodic theorem - mean value theorem - normal form theorem - ratio limit theorem - rational root theorem - second mean value theorem - theorem of consistency proofs - theorem of corresponding states - three line theorem - three series theorem - uniform convergence theorem - uniform ergodic theorem - uniform mean value theoremtheorem implies — из теоремы следует, что…
См. также в других словарях:
Maximum modulus principle — A plot of the modulus of cos(z) (in red) for z in the unit disk centered at the origin (shown in blue). As predicted by the theorem, the maximum of the modulus cannot be inside of the disk (so the highest value on the red surface is somewhere… … Wikipedia
Singular value decomposition — Visualization of the SVD of a 2 dimensional, real shearing matrix M. First, we see the unit disc in blue together with the two canonical unit vectors. We then see the action of M, which distorts the disk to an ellipse. The SVD decomposes M into… … Wikipedia
окончательное среднее значение модуля упругости — Emean,fin — [Англо русский словарь по проектированию строительных конструкций. МНТКС, Москва, 2011] Тематики строительные конструкции Синонимы Emean,fin EN final mean value of modulus of elasticity … Справочник технического переводчика
List of mathematics articles (M) — NOTOC M M estimator M group M matrix M separation M set M. C. Escher s legacy M. Riesz extension theorem M/M/1 model Maass wave form Mac Lane s planarity criterion Macaulay brackets Macbeath surface MacCormack method Macdonald polynomial Machin… … Wikipedia
rock — rock1 rockless, adj. rocklike, adj. /rok/, n. 1. a large mass of stone forming a hill, cliff, promontory, or the like. 2. Geol. a. mineral matter of variable composition, consolidated or unconsolidated, assembled in masses or considerable… … Universalium
Rock — /rok/, n. a male given name. * * * I In geology, a naturally occurring and coherent aggregate of minerals. The three major classes of rock igneous, sedimentary, and metamorphic are based on the processes that formed them. These three classes are… … Universalium
Riemann zeta function — ζ(s) in the complex plane. The color of a point s encodes the value of ζ(s): dark colors denote values close to zero and hue encodes the value s argument. The white spot at s = 1 is the pole of the zeta function; the black spots on the… … Wikipedia
Hardy space — In complex analysis, the Hardy spaces (or Hardy classes) Hp are certain spaces of holomorphic functions on the unit disk or upper half plane. They were introduced by Frigyes Riesz (Riesz 1923), who named them after G. H. Hardy, because of the… … Wikipedia
List of real analysis topics — This is a list of articles that are considered real analysis topics. Contents 1 General topics 1.1 Limits 1.2 Sequences and Series 1.2.1 Summation Methods … Wikipedia
analysis — /euh nal euh sis/, n., pl. analyses / seez /. 1. the separating of any material or abstract entity into its constituent elements (opposed to synthesis). 2. this process as a method of studying the nature of something or of determining its… … Universalium
List of mathematical symbols — This is a listing of common symbols found within all branches of mathematics. Each symbol is listed in both HTML, which depends on appropriate fonts being installed, and in TeX, as an image. This list is incomplete; you can help by expanding it.… … Wikipedia